بررسی تجربی انتقال حرارت و کارایی پره سهموی در شار حرارتی، سرعت جریان و زوایای پره مختلف

نوع مقاله : مقاله پژوهشی

نویسندگان

1 استادیار عضو هیئت علمی دانشگاه پدافند هوایی خاتم الانبیاء(ص)

2 کارشناسی ارشد، گروه آموزشی مکانیک، دانشگاه پدافند هوایی خاتم‌الانبیاء(ص)، تهران، ایران

3 کارشناس، گروه آموزشی مکانیک، دانشگاه پدافند هوایی خاتم‌الانبیاء(ص)، تهران، ایران

چکیده
در این پژوهش تأثیر عواملی مانند سرعت و دمای جریان خنک‌کننده، شار حرارتی و زاویه قرارگیری پره بر میزان انتقال حرارت بررسی شده است. برای این منظور از پره‌ی سهموی مقعر با زوایای ۰، ۴۵ و ۹۰ درجه نسبت به جریان خنک کننده (هوا)، سرعت جریان (بین 1 تا 5/2 متر بر ثانیه) و شار حرارتی 5/18 و 6/4 کیلووات بر متر مربع استفاده شده است. به دلیل رسانایی حرارتی بالا، جنس پره از فلز آلومینیوم انتخاب گردیده است. نتایج نشان داد که نوک تیز و انحنای پره سهموی علاوه بر کاهش وزن و حجم پره سهموی نسبت به پره مثلثی، موجب بهبود یکنواختی جریان و افزایش سطح تماس حرارتی و در نتیجه کاهش افت فشار و تنش‌های حرارتی و افزایش طول عمر پره می‌گردد. انتهای بسیار تیز پره سهموی باعث کاهش پدیده‌های گردابی و تغییرات ضریب انتقال حرارت شده و با افزایش سرعت جریان، میانگین ضریب انتقال حرارت افزایش می‌یابد. همچنین تغییر زاویه بین جریان سیال و امتداد پره تأثیر چندانی بر کارایی پره‌ها نداشته و افت فشار تنها به سرعت جریان وابسته است؛ به‌طوری‌که کمترین افت فشار در زاویه برخورد صفر درجه مشاهده شد. افزایش سرعت جریان به‌طور قابل‌توجهی منجر به افزایش افت فشار می‌شود، در حالی که تغییر زاویه پره و شار حرارتی تأثیرات کمتری بر افت فشار دارند. در زاویه برخورد صفر درجه، به دلیل کاهش مقاومت سطح مقطع پره در برابر جریان، کمترین میزان افت فشار مشاهده شد.

کلیدواژه‌ها

موضوعات

عنوان مقاله English

Experimental Investigation of Heat Transfer and Efficiency of the Parabolic Fin under Various Heat Flux, Flow Velocity, and Fin Angles

نویسندگان English

Mohammad Pourjafargholi 1
alireza gholami 2
Mohammadreza Karimi 3
1 Assistant Professor, Faculty Member, Khatam Al-Anbiya Air Defense University
2 Department of Mechanical Engineering, Air Defense University, Tehran, Iran
3 Department of Mechanical Engineering, Air Defense University, Tehran, Iran
چکیده English

In this study, has been investigated the effects of key parameters, including coolant flow velocity and temperature, heat flux, and fin angle, on heat transfer performance. For this purpose, a concave parabolic fin has been used with angles of 0, 45, and 90 degrees relative to the coolant flow (air), flow velocity (between 1 and 2.5 m/s), and heat flux of 18.5 and 4.6 kW/m2. Due to its high thermal conductivity, the fin material has been selected aluminum. Results reveal that the parabolic fin's sharp-tip and curvature not only reduce its weight and volume compared to a triangular fin but also improve flow uniformity and thermal contact area. This leads to reduced pressure drop and thermal stresses, ultimately enhancing fin durability. The parabolic fin’s sharp end further minimizes vortex formation and variations in the heat transfer coefficient, and as flow velocity increases, the average heat transfer coefficient rises. Moreover, the analysis shows that changes in the angle between the fluid flow and fin alignment have minimal impact on fin efficiency, with pressure drop primarily influenced by flow velocity. The lowest pressure drop occurs at a flow angle of zero degrees. Additional, findings indicate that while an increase in flow velocity substantially raises pressure drop, changes in fin angle and heat flux have less pronounced effects. At zero-degree flow alignment, the minimal cross-sectional resistance of the fin results in the lowest observed pressure drop.

کلیدواژه‌ها English

Heat transfer in fins
parabolic geometry
flow angle
experimental study
[1]        Y. Tomar and M. Sahu, "Review of performance analysis of extended surfaces (fins) under free and forced convection heat transfer," International Journal of Innovative Research & Development, vol. 2, pp. 73-78, 2013.
[2]        A. Walunj, V. Daund, and D. Palande, "Review of Performance of Rectangular Fins under Natural Convection at Different Orientation of Heat Sink," International Journal of Innovation and Applied Studies, vol. 6, No. 2, p. 232, 2014.
[3]        A. M. Abdulateef, S. Mat, J. Abdulateef, K. Sopian, and A. A. Al-Abidi, "Geometric and design parameters of fins employed for enhancing thermal energy storage systems: a review," Renewable and Sustainable Energy Reviews, vol. 82, pp. 1620-1635, 2018.
[4]          V. Madhavadas, D. Das, K. A. Mohta, and S. S. Prabu, "Comparative analysis on heat transfer of various fin profile using solid works: A systematic review," in IOP Conference Series: Earth and Environmental Science, 2021, vol. 850, No. 1: IOP Publishing, p. 012029.
[5]          A. S. Sorathiya, H. P. Hirpara, and P. Rathod, "An Effect of Different Parameters of Fins on Heat Transfer of IC Engine-Review Study," IOSR Journal of Mechanical and Civil Engineering, vol. 11, pp. 63-71, 2014.
[6]          T. A. Tahseen, M. Ishak, and M. Rahman, "An overview on thermal and fluid flow characteristics in a plain plate finned and un-finned tube banks heat exchanger," Renewable and Sustainable Energy Reviews, vol. 43, pp. 363-380, 2015.
[7]          H. D. Rathod, A. J. Modi, and P. P. Rathod, "Effect of Different Variables on Heat Transfer Rate of Four-Stroke Si Engine Fins Review Study," International Journal of Mechanical Engineering and Technology (IJMET), vol. 4, No. 2, 2013.
[8]          S. Chingulpitak and S. Wongwises, "A review of the effect of flow directions and behaviors on the thermal performance of conventional heat sinks," International Journal of Heat and Mass Transfer, vol. 81, pp. 10-18, 2015.
[9]          B. Freegah, A. A. Hussain, A. H. Falih, and H. Towsyfyan, "CFD analysis of heat transfer enhancement in a plate-fin heat sink with fillet profile: Investigation of new designs," Thermal Science and Engineering Progress, vol. 17, p. 100458, 2020.
[10]       S. Zaidshah and V. Yadav, "Heat transfer from different types of fins with notches with varying materials to enhance the rate of heat transfer a Review," International Journal of Applied Engineering Research, vol. 14, No. 9, pp. 174-179, 2019.
[11]      A. Tariq, K. Altaf, S. W. Ahmad, G. Hussain, and T. Ratlamwala, "Comparative numerical and experimental analysis of the thermal and hydraulic performance of improved plate-fin heat sinks," Applied Thermal Engineering, vol. 182, p. 115949, 2021.
[12]      P. Prasad and L. Prasad, "CFD analysis on the louvered fin," Int Res J Eng Technol, vol. 4, No. 1, pp. 1458-1462, 2017.
[13]      A. Hashem-ol-Hosseini, M. A. Ghazani, and M. D. Emami, "Experimental study and numerical simulation of thermal-hydraulic characteristics of a finned oval tube at different fin configurations," International Journal of Thermal Sciences, vol. 151, p. 106255, 2020.
[14]       B. Jalili, N. Aghaee, P. Jalili, and D. D. Ganji, "Novel usage of the curved rectangular fin on the heat transfer of a double-pipe heat exchanger with a nanofluid," Case Studies in Thermal Engineering, vol. 35, p. 102086, 2022.
[15]      M. A. Ali and S. Kherde, "Design Modification and Analysis of Two-Wheeler Cooling Fins-A Review," International Journal of Advances in Engineering & Technology, vol. 7, No. 3, pp. 998-1002, 2014.
[16]      I. Satyanarayana and G. Pranay, "Design and analysis of rectangular and triangular fins using CFD," International Journal of Scientific Engineering and Technology Research, vol. 5, No. 31, pp. 6554-6564, 2016.
[17]       R. Vijayakumar, T. Nithyanandam, A. Janarthanan, N. Jeevanantham, and B. Santhosh, "Analysis of Rectangular Fins Using CFD," Annals of the Romanian Society for Cell Biology, pp. 1892-1898, 2021.
[18]       P. K. Singh, V. K. Sharma, and A. Islam, "Numerical analysis on thermal properties of aluminum alloy for transforming heat-based applications," Materials Today: Proceedings, vol. 45, pp. 3596-3600, 2021.
[19]       S. Durgam, A. Kale, N. Kene, A. Khedkar, S. Palve, and N. M. Gawai, "Thermal analysis of fin materials for engine cylinder heat transfer enhancement," in IOP Conference Series: Materials Science and Engineering, 2021, vol. 1126, No. 1: IOP Publishing, p. 012071.
[20]       H. Nguyen and A. Aziz, "Heat transfer from convecting-radiating fins of different profile shapes," Wärme-und Stoffübertragung, vol. 27, No. 2, pp. 67-72, 1992.
[21]       A. Aziz and T. Fang, "Alternative solutions for longitudinal fins of rectangular, trapezoidal, and concave parabolic profiles," Energy Conversion and Management, vol. 51, No. 11, pp. 2188-2194, 2010.
[22]       M. Torabi, A. Aziz, and K. Zhang, "A comparative study of longitudinal fins of rectangular, trapezoidal and concave parabolic profiles with multiple nonlinearities," Energy, vol. 51, pp. 243-256, 2013.
[23]       R. Karvinen and T. Karvinen, "Optimum geometry of plate fins," Journal of heat transfer, vol. 134, No. 8, 2012.
[24]       A. Aziz and A. D. Kraus, "Transient heat transfer in extended surfaces," 1995.
[25]        N. Mani and V. K. Pandey, "Heat Transfer Phenomenon of Extended Surfaces in Form of Fins with Internal and External Configurations: A Review."
[26]       M. Mashud, M. I. Inam, Z. R. Arani, and A. Tanveer, "Experimental investigation of heat transfer characteristics of the cylindrical fin with different grooves," International Journal of Mechanical & Mechatronics Engineering IJMME, vol. 9, No. 10, 2009.
[27] M. pourjafargholi, A. Gholami, and M. Karimi, "Investigating fin heat transfer in rectangular, triangular and parabolic geometries in singular and groups under laminar and turbulent cooling airflow," Journal of Aerospace Defense, vol. 2, no. 2, pp. 55-83, (2023).
[28]        M. pourjafargholi, A. Gholami, and M. Karimi, "Experimental investigation of fin heat transfer characteristics in a different condition," AUT Journal of Mechanical Engineering, vol. 8, No. 2, pp. 5-5, 2024, doi: 10.22060/ajme.2024.23065.6096.
[29]       F. P. Incropera, D. P. DeWitt, T. L. Bergman, and A. S. Lavine, Fundamentals of heat and mass transfer. Wiley New York, 1996.
[30]       C.-H. Huang and P.-W. Tung, "Numerical and experimental studies on an optimum Fin design problem to determine the deformed wavy-shaped heat sinks," International Journal of Thermal Sciences, vol. 151, p. 106282, 2020.
[31]       E. Buckingham, "On physically similar systems; illustrations of the use of dimensional equations," Physical Review, vol. 4, No. 4, p. 345, 1914.
[32]      J. G. Collier and J. R. Thome, Convective boiling and condensation. Clarendon Press, 1994.
[33]      R. J. Moffat, "Describing the uncertainties in experimental results," Experimental thermal and fluid science, vol. 1, No. 1, pp. 3-17, 1988.
دوره 3، شماره 3
پاییز 1403
صفحه 1-25

  • تاریخ دریافت 27 مرداد 1403
  • تاریخ بازنگری 09 مهر 1403
  • تاریخ پذیرش 19 آبان 1403